Hidden Curtain Rod Brackets
Brushed Nickel · Set of 3 · Screws Under a Magnetic Cover
Three brushed nickel brackets with the screws hidden under a magnetic cover: two for the ends of the rod and one for the middle of a wide window. The arm adjusts from 3.5 to 5 inches and holds a 1-inch rod.
$19.99
Buying for a project or a store? Trade pricing from one master carton
Screws out of sight on all three
Each wall plate gets a magnetic cover, so there are no screw heads anywhere along the rod.
How it’s doneA center bracket for wide windows
The third bracket holds the middle of a long rod, and its screws are covered too.
Wide windowsAdjusts from 3.5 to 5 inches
Slide the arm to the depth you need on a standard 1-inch rod.
Set the depth
How These Hidden Curtain Rod Brackets Hide the Screws
The screws still do the work. They go through the wall plate into a stud, an anchor or masonry, the same as with any bracket. Then a brushed nickel cover goes over the plate and a magnet holds it in place.
Be clear on what’s hidden: the screws, not the bracket. The arm and the cradle stay in view at each end of the rod.
The screws stay reachable
Hidden doesn’t mean sealed. Pull the cover off by hand and the screws are right there. Tighten one if a plate ever works loose, then press the cover back on.
Fits your window?
3.5–5 in from the wall. Three brackets with magnetic covers included.
A Clean Line Across a Wide Window
A wide window needs three brackets, and three brackets means three sets of screws on the wall. The one in the middle sits right at the center of the view. With the covers on, all three look the same: smooth plate, straight arm, cradle. The rod reads as one clean line.
What the center bracket does
A long rod held only at its ends bows in the middle. The center bracket gives it a third point of support. Mount it halfway between the end brackets, at the same height and the same depth. Hang one curtain panel on each side: rings can’t pass it.
For bracket spacing on longer rods, see how many curtain rod brackets you need. The same three-bracket set in black is the extendable curtain rod brackets.
Depth: 3.5 to 5 inches
Loosen the screws on the arm, slide it to the depth you need and tighten them. Use the slider to check whether 5 inches clears your trim or blind.
Brushed Nickel on Light Walls
Hardware that blends into the wall
On white, cream or pale gray walls, brushed nickel is a low-contrast finish. Add hidden screws, and the hardware almost blends into the wall, leaving the curtains to do the talking. That’s the point of this set.
It fits coastal, Scandinavian and soft modern rooms. Pair it with white, ivory or sand curtains and a brushed nickel or satin silver rod.
Specifications and What’s in the Box
Key specifications
- Bracket Projection
- 3.5–5 in (adjustable)
- Fits Rod Diameter
- 1 in rods
- Pack Size
- Set of 3
- Mounting Type
- Wall
- Material
- Alloy Steel
- Color
- Brushed Nickel
Product details
- Product Type
- Curtain Rod Brackets
- Brand
- A Key Tech
- Model Number
- MCCRB 3-5
- Item Weight
- 13.4 oz
- Amazon ASIN
- B0FPRKW83D
Three brackets for a wide window
Two brackets go a few inches past each side of the frame, so the curtains stack beside the glass. The third goes in the middle. For a standard window with no center support, the decorative curtain rod brackets in a set of 2 are the same bracket and finish.
What’s in the box
How to Install Hidden Curtain Rod Brackets
Tools: a drill, a screwdriver, a level, a tape measure and a pencil.
- 1Match the arms
- 2Mark the ends
- 3Mark the middle
- 4Drill and mount
- 5Hide the screws
- 6Thread the curtains
- 7Set the rod
- Step 1 of 7
Match the arms. Set all three arms to the same depth and tighten the screws on each.
- Step 2 of 7
Mark the ends. Mark the two end brackets at the same height, a few inches past each side of the frame.
- Step 3 of 7
Mark the middle. Mark the center bracket halfway between them, at the same height. Check the three marks with a level.
- Step 4 of 7
Drill and mount. Mark the plate holes, drill and screw each bracket to the wall. Use anchors in drywall unless you hit a stud.
- Step 5 of 7
Hide the screws. Press a magnetic cover onto each of the three wall plates.
- Step 6 of 7
Thread the curtains. Put one panel on each half of the rod.
- Step 7 of 7
Set the rod. Lay it in the two end cradles first, then in the center one.
Hidden Screw vs 5-Inch vs Ceiling Brackets
Hidden Screws
- Holds
- —
- Projection
- 3.5–5 in
- Fits rods
- 1 in rods
- Mount
- Wall
5-Inch Over Blinds
- Holds
- —
- Projection
- 5 in
- Fits rods
- 3/4 in to 1 in rods
- Mount
- Wall
Ceiling Mount
- Holds
- 5 lb
- Projection
- 3 in
- Fits rods
- 3/4 in to 1 in rods
- Mount
- Ceiling or Wall
- Choose these hidden curtain rod brackets for a wide window where no screw heads should show and 3.5 to 5 inches of depth is enough.
- Choose the 5-inch over blinds brackets for a fixed depth over horizontal blinds.
- Choose the ceiling curtain rod brackets to mount the rod on the ceiling, or the brushed nickel flush mount curtain rod brackets to keep it close to the wall.
- For heavy drapes with a stated rating, see the heavy duty curtain rod brackets, rated 25 lb per bracket.
This bracket in black, set of 2: magnetic curtain rod brackets.
Wholesale and Bulk Orders
Trade pricing for interior designers, contractors, property managers, hospitality suppliers and stores.
Or call +1 267 986 1426, 9 AM–6 PM Eastern.
- 30–50 unitsMinimum per finish: one master carton, by model
- 20%+ offRetail price, better with volume
- 1 business dayIn-stock orders ship from Pennsylvania
- SamplesCheck the finish and build first
FAQ
Hidden screws, the covers and the center bracket.
How are the screws hidden?
Each bracket has a wall plate that you screw to the wall as usual. A brushed nickel cover then snaps over the plate and a magnet holds it there. The screw heads end up behind the cover, so the wall side of every bracket looks smooth.
Are the brackets themselves hidden?
No. The screws are hidden; the arm and cradle stay visible. If you’re after a bracket that disappears completely, a wall bracket of any kind won’t do that.
Can I tighten the screws after the covers are on?
Yes. Pull the cover off by hand, tighten the screw and press the cover back.
Does the center bracket hide its screws too?
Yes. All three brackets in the set are identical, each with its own magnetic cover. The center one looks the same as the two at the ends.
Can I buy these brackets in bulk?
Yes. Trade pricing starts at one master carton per finish, 30 or 50 units depending on the model, with discounts from 20% off retail that grow with volume. In-stock orders ship from our Pennsylvania warehouse within one business day. See partner pricing or email [email protected].
